Land Pride RCM5020
Features
| Features | Benefits |
| Surpassed rugged industry standards |
All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures specified by ANSI. |
| Factory assembled | Saves customer set-up time and money. |
| Fully welded deck | Fully welded deck adds strength. |
| 250 HP Divider gearbox 210 HP center & wing gearboxes |
A rugged heavy built gearboxes capable of handling heavy cutting applications. |
| Gearbox seal protection | Gearbox bottom seal protection for longer bearing life. |
| Input driveline: Cat. 6 CV or Cat. 5 Conventional |
Holds up to shock loads and harsh mowing conditions. Fits wide range of tractors including high horsepower tractors. |
| Star profile drivelines | Star profile spreads load out to many points on the shaft. More apt to resist bending and twisting under shock loads and harsh mowing conditions. |
| Easy greasable drivelines | Drivelines have access holes for greasing the U-joints and to grease the inner profiles. |
| 4 Plate slip-clutch | Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when impacts are encountered. |
| High blade tip speed | 540 rpm: Center: 17,377 fpm, Wings: 17,329 fpm 1000 rpm: Center: 18,165 fpm, Wings: 15,013 fpm Allows for a clean cut of material and even distribution. |
| 6" Blade overlap | Generous blade overlap eliminates skipping, especially in turns. |
| High cutting capacity | Can cut brushy areas with saplings up to 3". |
| Left wing rotates counterclockwise | Better discharge of material. Picks up tractor tracks. |
| 10 1/2" Deck height | Handles heavy cutting, which reduces balling-up of cut material under the deck. |
| 3/16" Stump jumper backed with a 1" thick mounting bar |
Heavy round stump jumper with bottom gearbox seal protector. Can hold up to tough conditions. |
| 3/16" Deck thickness | Heavy enough to handle conditions but not weigh unit down. |
| Self-leveling pull-type hitch | Reduces drawbar wear by keeping hitch level while going through ditches. |
| LED Signal lights | LED lights are bright, long lasting, and resistant to vibration, unlike incandescent counterparts. |
| Hinged wing sections | Allow cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting. |
| 1" Solid hinge rods | Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in the hinge area itself. |
| Wing transport locks | Safety feature. Holds wing sections up in case of hydraulic pressure loss. |
| Enclosed front to rear dual leveling rods |
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod. |
| Drain holes in wheel rims | Allows water to drain from wheels mounted on the folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims. |
| 5" Square rear axle tubing | Heavy axle to handle harsh conditions. |
| Spring-cushioned center-axle | Protects unit from bumps and ground shock. |
| Replaceable wheel spindles | Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove two bolts to replace damaged spindle. |
| Double swivel hitch | Great for uneven terrain, reduces drawbar wear. |
| Bar-tite hitch | Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear. |
| Wheel options | Laminated tires: Eliminates flats. Airplane tires without foam filling: Give better cushion while transporting. Airplane tires with foam filling: Give better cushion while transporting and can’t go flat. |
| Deck rings (optional) | 1/2" x 3" full welded deck ring keeps blades from damaging the deck. |
| Shredder Blades (Optional) | Ideal for cutting residue into smaller pieces. Replaces blade and stump jumper configuration. |
| Baffles (Accessory) | Maintains shredded material in each section of the cutter for a consistent discharge from the rear of each deck. |
Specifications
| Specifications & Capacities | RCM5020 |
| Min. horsepower | 90 power take-off horsepower (67.1 kw) |
| Gearbox horsepower | 250 (186.4 kw) Splitter 225 (167.8 kw) Center deck & wing decks |
| Gearbox lubrication & capacity |
Center deck & wings: 10 pints (4.73 L) of gear lube 80-90W EP Divider gearbox: 5.5 pints (2.60 L) of gear lube 80-90W EP |
| Cutting capacity | Up to 3" (7.6 cm) material |
| Machine weight | 7,340 lbs. (3,329.4 kg) |
| Blade tip speed At 540 rpm At 1000 rpm |
Center blade: 17,377 FPM (88.3 mps) & wing blade: 17,329 FPM (88 mps) Center blade: 18,165 FPM (92.3 mps) & wing blade: 18,317 FPM (93.1 mps) |
| Tongue weight | 2,668 lbs. (1,210.2 kg) |
| Hitch types | Standard clevis hitch, pintle hitch, ball hitch, LP performance hitch and bar-tite hitch |
| Hitch jack | Standard hand crank |
| Signal lights 7 Pin connector |
LED (standard) SAE J560 pin configuration |
| Cutting width Overall width Minimum transport width |
20'-0" (6.10 m) 20'-10" (6.35 m) 8'-9" (2.44 m) |
| Overall length | 19'-3" (5.87 m) |
| Deck height | 10 1/2" (3.06 m) |
| Cutting height* | 2" (5.1 cm) to 14" (35.6 cm) with hydraulic cylinder and stroke control spacers |
| Lift hydraulics | 4" x 8" Hydraulic cylinder, hoses, fittings & stroke control spacers |
| Wing hydraulics | 3 1/2" x 12" Hydraulic cylinders, hoses & fittings |
| Wing transport protection | Wing transport locks |
| Deck sheet thickness | 10g (3.4 mm) top and 10g (3.4 mm) bottom |
| Side skirt thickness | 1/4" (6 mm) |
| Skid shoes Wing decks Center deck |
Replaceable and reversible Replaceable |
| Blades - 6 (2 per carrier) | 1/2" (13 mm) x 4" (10.2 cm) Heat-treated, free-swinging alloy steel with uplift |
| Blade overlap | 6" (16.2 cm) |
| Blade bolt | Keyed with hardened flat washer & locknut |
| Stump jumper Blade holder |
3/16" (5 mm) Round dish shaped bolt-on stump-jumper (optional) 1" (2.5 cm) diamond shaped blade bar |
| Deck rings (optional) | 1/2" (13 mm) x 3" (7.6 cm) fully welded |
| Front & rear guards | Single chain or double chain |
| Heavy duty Input driveline options |
Constant velocity u-joint ASAE Cat. 6 with or without over running clutch |
| Heavy duty Intermediate & wing drivelines |
ASAE Cat. 5 with slip-clutch protection |
| Tire & wheel options | 6" x 21" Laminated tires 6" x 26" Laminated tires 27" x 7.75" x 15" Used aircraft tires with foam filling 29" Used aircraft tires |
| Number of wheel | 6 - Wheel option: 4 on transport axle and one on each wing axle 8 - Wheel option: 4 on transport axle and two on each wing axle |
| Transport axle | Spring-cushioned on center transport axle or optional walking tandem on center axle |
| Hubs | Cast iron 5-bolt hubs with tapered roller bearings and with 1 3/4" (4.4 cm) shafts |
| Shredder blades (optional) | Cuts material into smaller pieces |
| Baffle Kit (optional) | Front & rear mounted |
| * Maximum cut height is dependent on tire options selected. | |