Land Pride RC4715
Features
| Features | Benefits |
| Surpassed rugged industry standards | All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13. |
| Factory assembled | Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit. |
| Rugged heavy built gearboxes | Capable of handling heavy cutting applications. |
| Gearbox seal protection | Gearbox bottom seal protection for longer bearing life. |
| Sliding guard for splitter gearbox | Sliding guard offers protection and easy access for improved efficiency of splitter gearbox maintenance. |
| 2 Piece driveline shields | Driveline grease zerks are easier to access. |
| Low hitch weight on tractor tongue | Ideal for smaller hp tractors by reducing the amount of weight on the drawbar. |
| Narrow A-frame hitch | Allows for a tighter turning radius. |
| Adjustable park jack angle | Park jack can be adjusted to be perpendicular to the ground. |
| Adjustable driveline hanger | Serves as support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to tractor power take-off shaft. |
| Input driveline: Cat. 6 CV | Driveline is matched just right for tractor capacity. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline. |
| Drivelines with slip-clutches: Cat. 4 intermediate Cat. 4 or Cat. 5 wings |
Driveline is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to driveline profiles. |
| Grease zerks on end caps of driveline | Intermediate and wing driveline cross journals are easier to grease. |
| High blade tip speed | Allows clean cutting of material. |
| 6" Blade overlap | Eliminates skipping during turns. |
| Diamond blade bar | Provides the critical strength needed for consistent, top performance. |
| 3/16" Round stump jumper | Standard thick stump jumper material keeps damage to a minimum. |
| Smooth top design | Reduces accumulation of debris and is easier and faster to clean. |
| Tops of decks are 100% welded | Makes center decks and wing decks stronger. |
| 1/4" Sidewall thickness | Increased thickness reduces damage from objects being thrown into deck sidewalls. |
| Multiple center skid shoe locations | Run two or four skid shoes in locations under the tongue pivots or out at the wing hinges. |
| Beveled skid shoes on wings | Reduces gouging the ground when turning. |
| LED signal lights | LED lights are bright, long lasting, and resist vibration, unlike incandescent lights. |
| Hinged wing sections | Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting. |
| 1" Solid hinge rods | Larger diameter hinge rod provides greater strength in the hinge area. |
| Wing transport lock pins | Transport lock pins will hold wings in folded position in the event of hydraulic loss. |
| Enclosed dual 1" leveling rods | Cutter pulls equally on the rear axle while traveling over rough terrain. |
| 5-Bolt hubs | 5-Bolt hubs makes the wheel assembly more durable and longer lasting. |
| Drain holes in wheel rims | Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims. |
| Spring cushioned center-axle | Protects unit from bumps and ground shock. |
| Optional spring cushioned wing-axles | Further improves ride over a multitude of terrains. |
| Replaceable individual wheel spindles | Spindles can be replaced when damaged without replacing entire axle assembly. |
| Wheel options | Laminated tires: Eliminates flats. Air-filled tires: Give better cushion while transporting. Foam-filled tires: Give better cushion while transporting and can’t go flat. |
| LP Performance hitch option | Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar up to 12 degrees in both left and right directions. |
| Bar-tite hitch option | Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear. |
Specifications
| Specifications & Capacities | RC(M)4715 & RCG(M)4715 |
| Horsepower range | 55 - 250 hp |
| Gearbox horsepower | 540 rpm or 1000 rpm 250hp (186.4 kW) Divider and 210hp (156.6 kW) Center & Wings |
| Gearbox lubrication | Gear Lube 80-90W EP |
| Gearbox oil capacity | Splitter: 3.5 pints (1.66 L); Center deck & Wings: 6 pints (2.84 L) |
| Cutting capacity | 4" (10.2 cm) |
| Machine weight Total weight Tongue weight |
5,000 lbs. (2268 kg) 1860 lbs. (843.7 kg) |
| Blade tip speed At 540 rpm At 1000 rpm |
Center Blades & Wing Blades = 16,300 FPM (82.8 mps) Center Blades = 16,300 FPM (82.8 mps) & Wing Blades = 16,000 FPM (81.3 mps) |
| Hitch types | Swivel Clevis Hitch, LP Performance Hitch, Bar-Tite Hitch, Ball Hitch, or Pintle Hitch. |
| Hitch jack | Standard (7,000 lbs.) (3175.1 kg) |
| Signal lights 7 Pin connector |
LED SAE J560 pin configuration |
| Cutting width Overall width Transport width with 21" tires |
15'-0" (4.57 m) 15'-10" (4.83 m) 10'-3" (3.12 m) - Single-acting fold option, 7’-3" (2.21 m) - Dual-acting fold option. |
| Overall length | 16'-3" (4.95 m) - With center deck raised fully up. |
| Deck height | 12" (30.5 cm) |
| Cutting height | 1-1/2" - 16" (3.8 cm - 40.6 cm) - Varies by tire option. |
| Lift hydraulics | 3" x 8" (7.6 cm x 20.3 cm) hydraulic cylinder, hoses, fittings & stroke control spacers. |
| Wing hydraulics | 2 1/2" x 12" (6.4 cm - 30.5 cm) hydraulic cylinders, hoses & fittings. |
| Wing transport protection | Wing Transport Lock Pins |
| Deck material thickness | 10 Gauge (3.4 mm) |
| Side skirt thickness | 1/4" (6 mm) Steel |
| Skid shoes | Wing Deck: 1 Replaceable skid shoe per wing. Center Deck: 2 Replaceable skid shoes and multiple mounting locations. |
| Blades - 6 (2 per carrier) | 1/2" x 4" (1.3 cm - 10.2 cm) Heat-treated, free-swinging alloy steel with uplift. |
| Blade overlap | 6" (15.2 cm) |
| Blade bolt | Keyed with hardened flat washer & locknut. |
| Stump jumper / blade holder | 3/16" (5 mm) Thick round dish shaped pan, reinforced with 1" x 4" (2.5 x 10.2 cm) blade bar. |
| Front & rear guards | Optional single row chain or dual row chain. |
| Input driveline 540 & 1000 rpm | Cat. 6 with constant velocity u-joint with or without overrunning clutch. |
| Intermediate driveline | Standard - Category 4 with slip-clutch. |
| Wing drivelines | Standard - Category 4 with slip-clutch or Category 5 with slip-clutch. |
| Wheel options | 21" (53.3 cm) or 26" (66 cm) Laminated tires 24" (61 cm) Used aircraft, foam filled tires 25.5" (64.8 cm) 20 ply tires, foam filled or pneumatic 29" (73.7 cm) Used aircraft tires |
| Number of wheels | 6 - Wheel option: Four on transport axle and one on each wing axle. 8 - Wheel option: Four on transport axle and two on each wing axle. |
| Transport axle | Many configurations to choose from. |
| Hubs | Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts. |
| LP Performance hitch & Bar tite hitch pivot shaft diameter | 2 1/4" (5.7 cm) |
| A-frame tongue | 5" x 3" (12.7 cm x 7.6 cm) rectangular tubing |